Tdk 500A Manuale Utente Pagina 1

INSTRUCTION MANUAL FOR 500A/102A/152A/202A POWER SUPPLY Document: 83-493-001 Rev. K TDK-Lambda Americas 405 Essex

83-493-001 Rev. K 2CHAPTER 2 SPECIFICATIONS 2.1 AVERAGE CHARGING RATE 500J/s, 1000J/s, 1500J/s, 2000J/s at rated Output Voltage 2.2 PEAK CHARGING

83-493-001 Rev. K 3 2.9 POWER FACTOR Non PFC PFC All models 0.65 0.98 Table 2-3 Power Factor 2.10 EFFICIENCY Better than 85% 2.11 STORED ENE

83-493-001 Rev. K 4 2.22 ACCESSORIES • Detachable 8 feet (2.4 meters) HV Cable (see Table 2.1) • 15 pin “D” plug mating control connector • Opera

83-493-001 Rev. K 5D Figure 2-1 Mechanical Dimensions for 500A, 102A, 152A

83-493-001 Rev. K 6 Figure 2-2 Mechanical Dimensions for 500A, 102A, 152A Outputs from 7KV to 40KV (for gro

83-493-001 Rev. K 7 Figure 2-3 Mechanical Dimensions for 202A Outputs up to 6KV (for grounding instru

83-493-001 Rev. K 8 Figure 2-4 Mechanical Dimensions for 202A Outputs from 7KV to 40KV (for grounding

83-493-001 Rev. K 9CHAPTER 3 INSTALLATION 3.1 INITIAL INSPECTION The shipping container should contain the following items: power supply, HV outpu

83-493-001 Rev. K 10TB1L1COML2230 VAC115 VACTB1L1COML2115-2 30 VAC Figure 3-1 Input AC Power Connection NON-PFC Version F

83-493-001 Rev. K 11 3.5 CONNECTING HIGH VOLTAGE OUTPUT POTENTIAL LETHAL VOLTAGE Ensure that the power supply is off and disconnected from the

THIS PAGE INTENTIONALLY BLANK

83-493-001 Rev. K 123.6 GROUNDING THE PRODUCT 3.6.1 GROUNDING OF INPUT LINE The supply is grounded through the ground terminal of the input connect

83-493-001 Rev. K 13CHAPTER 4 OPERATION 4.1 REMOTE CONTROL The Series 500A/102A/152A/202A is easily controlled through the remote connector on the

83-493-001 Rev. K 14 Figure 4-1 Example of Interface Connection

83-493-001 Rev. K 15 4.2 INITITIAL CHECK-OUT PROCEDURE LETHAL VOLTAGES PRESENT ONLY QUALIFIED PERSONNEL TRAINED IN THE SAFETY ASPECTS OF HIGH

83-493-001 Rev. K 16Peak Charge Rate = C - OUTPUT LOAD CAPACITOR12CV2TCV - PROGRAMMED OUTPUT VOLTAGEAverage Charge Rate = TC AND TP ARE SHOWN I

83-493-001 Rev. K 17A series terminating resistor (or series inductor or clamp diode) must be added as shown if the average value of the peak curre

83-493-001 Rev. K 185.4 MEASURING HIGH VOLTAGES A sample of the output voltage is available in the REMOTE connector. If it is desired t

83-493-001 Rev. K 19 Figure 5-3 HV Bias Measurements 5.5 DETERMINING AC LINE CURRENT IL = Line current P = Average output po

83-493-001 Rev. K 205.7 LONG CHARGE TIME WITH POWER FACTOR CORRECTED (PFC) UNITS It is advised that you consult the factory if this type of operati

83-493-001 Rev. K 21CHAPTER 6 MAINTENANCE AND CALIBRATION 6.1 SAFETY PRECAUTIONS ONLY QUALIFIED PERSONNEL TRAINED IN THE SAFETY ASPECTS OF

ONE YEAR WARRANTY TDK-Lambda Americas, Inc. (405 Essex Road, Neptune, N.J. 07753), warrants that the unit is free from defects in material or workmans

Product Name: UNIVOLT N 61 B Revision Date: 20Mar2007 Page 1 of 9 _______________________________________________________________________

Product Name: UNIVOLT N 61 B Revision Date: 20Mar2007 Page 2 of 9 _______________________________________________________________________

Product Name: UNIVOLT N 61 B Revision Date: 20Mar2007 Page 3 of 9 _______________________________________________________________________

Product Name: UNIVOLT N 61 B Revision Date: 20Mar2007 Page 4 of 9 _______________________________________________________________________

Product Name: UNIVOLT N 61 B Revision Date: 20Mar2007 Page 5 of 9 _______________________________________________________________________

Product Name: UNIVOLT N 61 B Revision Date: 20Mar2007 Page 6 of 9 _______________________________________________________________________

Product Name: UNIVOLT N 61 B Revision Date: 20Mar2007 Page 7 of 9 _______________________________________________________________________

Product Name: UNIVOLT N 61 B Revision Date: 20Mar2007 Page 8 of 9 _______________________________________________________________________

Product Name: UNIVOLT N 61 B Revision Date: 20Mar2007 Page 9 of 9 _______________________________________________________________________

TDK-Lambda MANUFACTURER'S PRODUCT DECLARATION INTENDED PURPOSE (USE) The Power Supplies described by this manual are defined by TDK-Lambda

TDK-Lambda Description of symbols used in product labeling SYMBOL PUBLICATION DESCRIPTION EC Council Directive 93/68/EEC European Community Con

01000680revD.sch-1 - Wed Jul 22 09:59:20 2009

ELECTRICAL STANDARDS All company primary standards are either certified or are traceable to certification by the National Institute of Standards and

9 83-493-001 Rev. KTABLE OF CONTENTS CHAPTER 1 INTRODUCTION ...

10 83-493-001 Rev. KCHAPTER 5 APPLICATIONS.......

83-493-001 Rev. K 1Control &Aux. PowerINPUT/POWERPFC / FusesInrush LimitHigh Freq.ResonantInverterStep-upTransformerHV Rect.HV FilterHV OU